Over the past two years or so my sewing room has turned into a bit of a mess. I am not a very tidy person by nature and the mess started to annoy even me. Now that I am using my room again on a much more regular basis (hurray!) things needed to change so I can make the most out of my limited sewing time. I’ve been thinking quite a bit about how to optimize the room and I have now found a solution for two of my main problems:
- Not having a set storage space for all those things that are used on a daily basis such as rulers, scissors, rotary cutters and pins. As a result I kept moving them from cutting table, to sewing table, to ironing board, to the floor and back to the cutting table, etc.. and often couldn’t find something that I desperately needed.
- I tend to work on several things at the same time and I don’t want to stuff these works in progress into a cabinet because I may forget about them if I don’t see them lying around, but at the same time it’s not ideal to keep moving piles of unfinished projects around the room.
Tadaa! Sometimes, even I am amazed at the things my mind comes up with.
From looking at a lot of sewing room pictures there are two things that are being used by a lot of people that seemed to have potential as a solution for my problems. The Ikea Raskog utility cart and pegboards. The Raskog looked useful since it can be moved around and it would be great as a temporary storage unit for works in progress, but it would not change the storage issue I have with my large quilting rulers, these are 60 cm long, while the cart is only 35×45 cm. Pegboards look really useful for storing rulers, but the one thing my sewing room lacks is empty wall space. Really, the only decent amount of wall space that I have is already in use by my design wall, and no way am I sacrificing that for a pegboard.
So, I had carts and pegboards on my mind and was thinking how it would be great to be able to hang my rulers from the Raskog cart since it’s 72 cm high. I then saw that the Ikea Skadis pegboard has a connector accessory that enables you to attach it to a table top instead of a wall and I realized that it might very well be possible to use this to attach the pegboard to the smaller side of the Raskog cart which would solve both problems in one go. My husband’s initial reaction when I told him that I planned to attach the pegboards I had bought to the cart that I was still assembling was “Whaaaaaaaat?!?”, but hey, I was right, it totally works and it is really easy!
So, today I have a tutorial so you can make your own mobile pegboard storage unit for your sewing room (or any other hobby I suppose) by combining two Ikea products, the Raskog utility cart and Skadis pegboard!
I’ve added the Ikea product numbers so you can easily find them on the Ikea website of your own country, links are to the US website since I expect most people that found this blog are able to read English.
- 1x Ikea Raskog ultility cart (white: 203.829.32, beige: 202.718.92, black: 903.339.76 or dark blue: 304.017.89)
- 2x Ikea Skadis pegboard 36×56 cm or 14 1/4×22’’ (white: 503.208.05 or wood: 703.471.73)
- 2x Ikea Skadis connector (2/pack, so you have 4 in total) (white: 103.207.89 or black: 703.207.91)
- 1x Ikea Fixa stick on floor protector set (241.556.00)
- 2x (white) tie wrap (I used ridiculously long ones, but 25 cm/10” is probably long enough)
- 4x screws/bolts, size M4, 10-12 mm length is probably ideal.
- Ikea Skadis accessories of your choice. On my pegboard I used:
Step 1: Assemble your Raskog trolley according to Ikea’s instructions.
Step 1: I decided to use the white cart with the white pegboard to make it appear that these 2 products really belong together.
Step 2: Stick a large circle of the Fixa floor protector set on each of the 4 Skadis connectors. There are 4 large circles in a pack so that works out great (we still had a pack at home with only 3 of the large circles left so I used some of the smaller ones on one of the connectors, this also worked). The connectors are made of metal and so is the Raskog cart. The felt protectors prevent scratching and also make it a bit easier to attach the connectors firmly.
Step 3: Attach the connectors to the pegboards, in the pegboard use the holes in the 4th column from the sides and on the connectors use the lower set of holes. Otherwise use the Ikea instructions.
Step 3 and 4: The left picture shows the side that will be facing the cart. The right picture shows the side that will be facing out.
Step 4: Each pegboard comes with 2 plastic spacer units that are normally used to make sure the pegboard hangs some distance from the wall. These are now used to make sure the pegboards end up in a good vertical position and an equal distance away from the cart baskets. The spacers should be attached to the same side as the part of the connectors that sticks out (see pictures). The screws that came with the pegboards have already been used to attach the connectors so this is where you need the 4 extra screws or bolts. They should end up positioned in the 9th column so that the top one touches the middle basket and the lower one the lower basket (and not the bolts that were used to attach the baskets to the cart). On both sides I attached the top one in the 9th hole from the bottom, but the lower one is in the 1st hole on one side and in the 3rd hole on the other side. Apparently my bottom basket ended up a bit lopsided even though I am pretty sure I followed the assembly instructions correctly. Simply try out what fits best before you firmly screw on your spacers.
Step 4: The plastic spacer and on the left the screw that it came with that you already used to attach the connector and on the right the bolt that I used instead. It’s much shorter than the original but this is fine.
Step 5: Attach the pegboards to the cart, this works best if you lay the cart on the floor so that the pegboard is horizontal. The spacers should end up exactly in the middle of the cart, you can use the bolts that were used to attach the baskets as a guide. Screw the connectors lightly to the cart. Test whether you can swivel both wheels of the cart. If you can’t, your pegboard is not centred correctly and you should reposition it. If you are happy with the placement, screw the connectors on tightly.
Step 5 Please note how I positioned the white plastic part of the screw so that there is enough space for the wheel to swivel.
Step 6: Use the tie wraps to attach the pegboard to the cart just above the second spacer unit. Position the closure so that it doesn’t get in the way when you put things in the basket and cut off the extra bit. Neglecting to add the tie wrap will result in a pegboard that topples forward as you hang things from it because the connectors were made to attach things to something square like a table and not to something round like this cart. With the tie wrap attached, the whole thing becomes really sturdy and everything will stay in place perfectly.
Step 7: Attach your chosen accessories to the pegboard and fill it up with tools, notions and projects.
Step 8: Enjoy a better organized sewing experience!
Some things to keep in mind
It is possible that not all of the Ikea products that I used are available in your country. I saw, for example, that in the US the Raskog cart does not come in white so you may have to use a different colour.
The Skadis pegboard has oblong shaped holes while most pegboards I’ve seen have round holes. As a result you may not be able to attach other accessories than the Ikea ones to this pegboard. Since the pegboards are not very large this did not really seem like a big problem to me since Ikea has several useful accessories, but you should realize this in case you have something very specific in mind.
Adding the pegboards does change the dimensions of the Raskog cart. The width doesn’t change that much, it goes from 35 to 36 cm, but the length increases quite a bit, depending on what you attach to it. If you only attach hooks and clips it changes from 45 to around 53 cm, if you add containers to both sides like I did, it goes easily up to 68 cm. It is, of course, possible to only add a pegboard to one side or to only use the containers on one side and hooks on the other side which limits the increase in length.
On my cart I am now using the storage bag and roll holder to store my rulers. After assembling the whole thing I realized that the long rulers could also hang from the pegboard if a hook is placed in the middle column of the pegboard so the bottom of the ruler doesn’t touch the wheels of the cart. However, the holes in my rulers do not work with the white hooks that I have because they’re not deep enough. Ikea also has black hooks that are a bit differently shaped (703.216.39), I think these may work with my Omnigrid rulers, but I currently don’t have these hooks so I am not entirely certain. I’ll probably pick them up next time I’m at Ikea but that will take some time since we don’t live next door. Edit August 4, 2018: I did try the black hooks and they work with the holes in the Omnigrid rulers (see picture below). However, the 24×6 inch ruler is too long and touches the floor, for now I am sticking with the storage bag and roll holder solution since I use this ruler all the time.
I hung the 12.5×12.5 inch and 60×15 cm rulers from the black hook and this works. The bottom of the 60×15 cm ruler is still a couple of milimeters away from the floor.
I advise against using the shelf accessory since things are bound to topple off when you move the cart around…
So, are you dashing off to Ikea to make your own mobile pegboard storage unit? If you do, I’d love to see a picture of your unit in use!